MCM Electronics MPA-10 Specifications

Please follow the instructions in this manual to obtain the optimum results from this unit.We also recommend that you keep this manual handy for futur

5. APPLICATIONS10TEL INPUTMIC2MIC1AUDIOOUTRLCOMAUDIO SOURCESLINKINPUTSXLR BAL1-GND2-HOT+3-COLD123123OUTPUTSINPUTSPOWER AMPLIFIERSPEAKERSLINEOUTAUXMIC

6. BLOCK DIAGRAMCOMPCOMPGAIN/AMPGAIN/AMPGAIN/AMPPOWER AMPGAIN/AMP11

7. SPECIFICATIONS12MIXER AMPLIFIER WITH CDMIXER AMPLIFIER WITH CDModelMPA-20Rated Power Output 40WMPA-40 20WSpeaker Line InputInput sensitivity/impe

100Over100OverOver100UNIT:mm8. DIMENSIONAL DIAGRAMUNIT:mm66464320273667432032013MIC1INPUTBASS TREBLEMIC2 TELOUTPUT LEVEL2 46810PROTPOWERMIC1AUXMASTERO

1. FEATURES1. Rated Power:60W \120W.2. 100V,70V constant voltage outputs and 4~16Ohms constant resistance output.3. Commercial-grade torroidal tra

2.1 60W/120W FRONT PANEL 1. MIC1 INPUT MIC1 input 6.3 Microphone jack input2. MIC1 \MIC2 \MIC3 MIC volume control (MIC1/MIC2/MIC3)3.

NOMENCLATURE AND FUNCTIONS2.2 60W/120W REAR PANEL13.~ 120V 60Hz POWER INPUT14. SPEAKER TERMINALS Connectors for 4-16 ohms or 70V and 100V

70V 100VCOM 4-16 70V 100VCOM 4-16 (MPA-60)167100V LINE70V 100VCOM 4-16 (MPA-60)8170V LINE3.1 SPEAKER CONNECTIONS 4-163. CONNECT

1 Tel has priority over all inputs. 2 MIC 1 is second priority, adjust mute electric potential can override other input signal

5. APPLICATIONS19AUDIOOUTRLCOMADRESS TAGAUDIO SOURCESLINKINPUTSXLR BAL1-GND2-HOT+3-COLD123123OUTPUTSINPUTSPOWER AMPLIFIERSPEAKERSMIC 2MIC1MIC 3TEL IN

TABLE OF CONTENTS2 SAFETY PRECAUTIONS ...3MPA-20,MPA-401. FEATURES...

6. BLOCK DIAGRAM70VCOM4TOPABASS/TREBLE VOLUMEPROTECTLEVEL INDICATORPOWER Z ~120V 60Hz PTCOM100VCOMEBEBLINE OUTMIC1MIC1MIC2MIC3AUX1AUX

7. SPECIFICATIONSMIXER AMPLIFIER WITH CDMIXER AMPLIFIER WITH CDModelMPA-12021MPA-60Speaker Line InputRated Power OutputInput sensitivity/impedanceS/

100Over100OverOver100UNIT:mm8. DIMENSIONAL DIAGRAMUNIT:mm68484303889443048422ONOFFMIC1INPUTBASS TREBLEMIC1MIC2 MIC3AUX1AUX2 TEL MASTERPOWER2PROTTEMP46

Be sure to read the instructions in this section carefully before use. Make sure to observe the instructions in this manual as the conventions of s

An all-pole mains switch with a contact separation of at least 3 mm in each pole shall be incorporated inthe electrical installation of the building.W

1. FEATURES1. Rated Power:20W and 40W.2. 100V,70V constant voltage outputs and 4~16Ohms constant resistance output.3. 1 channel MIC2 one-port input (

1 234985 6710112.1 20W/40W FRONT PANEL 1. MIC1 INPUT MIC1 input Microphone jack input2. MIC1 \MIC2 MIC volume control (MIC1/MIC2)3. AUX

NOMENCLATURE AND FUNCTIONS2.2 20W/40W REAR PANEL12. ~120V 60Hz AC POWER INPUT13.SPEAKER TERMINALS Connectors for 4-16 ohms or 70V and 100V

70V 100VCOM 4-16 70V 100VCOM 4-16 (MPA-20)500100V LINE70V 100VCOM 4-16 (MPA-20)24570V LINE3.1 SPEAKER CONNECTIONS 4-163. CONNEC

1 Tel has priority over all inputs. 2 MIC 1 is second priority, adjust mute electric potential can override other input signal